PlusQuip EQP-103 Скачать руководство пользователя страница 4

Страница: 4 / 57

Do not exceed voltage limits between inputs specified in

this user’s manual.

Always wear ANSI approved goggles to protect your eyes

from propelled objects as well as hot or caustic liquids.

Fuel, oil vapors, hot steam, hot toxic exhaust gases, acid,

refrigerant and other debris produced by a malfunction engine can

cause serious injury or death. Do not use code reader in areas where

explosive vapor may collect, such as in below-ground pits, confined

areas, or areas that are less than 18 inches (45 cm) above the floor.

Do not smoke, strike a match, or cause a spark near the

vehicle while testing and keep all sparks, heated items and open flames

away from the battery and fuel / fuel vapors as they are highly

flammable.

Keep a dry chemical fire extinguisher suitable for gasoline,

chemical and electrical fires in work area.

Always be aware of rotating parts that move at high speed

when an engine is running and keep a safe distance from these parts as

well as other potentially moving objects to avoid serious injury.

Do not touch engine components that get very hot when an

engine is running to avoid severe burns.

Block drive wheels before testing with engine running. Put

the transmission in park (for automatic transmission) or neutral (for

manual transmission). And never leave a running engine unattended.

Do not wear jewelry or loose fitting clothing when working

on engine.

Make sure to turn off ignition before connecting or

disconnecting the code reader.

EQP-103 User’s Manual

Содержание EQP-103


























































Результаты поиска

Содержание EQP-103

Отзывы:

Похожие инструкции для EQP-103

Бренды по названию

Популярные бренды

PlusQuip EQP-103, Руководство пользователя

Результаты поиска

Содержание EQP-103

Отзывы:

Похожие инструкции для EQP-103

Бренды по названию

Популярные бренды