PlusQuip EQP-103 Скачать руководство пользователя страница 38

Страница: 38 / 57

√

Trigger on DTCs

is picked, following screen displays:

√

If data is to be erased, select YES; if data is not be erased, pick

NO to return to

Select Memory

screen and pick another one.

Press the ENTER key to start recording or wait for codes

to trigger.

√

The code reader keeps saving data until:

•

memory is full;

•

the operator presses the BACK key.

NOTE Different vehicles communicate at different speeds and

support a different number of PIDs. Therefore, the maximum

number of frames that can be recorded varies.

After recording the code reader display a prompt to

Playback

Data

Trigger On DTC

Waiting for DTC to

trigger recording...

[BACK]-EXIT

Recording… 5/60

FUELSYS1

OL-Drive

FUELSYST2

N/A

LOAD_PCT %

0.0

ETC

°F

172

SHRTFT1 %

0.0

LONGFT1 %

0.0

EQP-103 User’s Manual

Содержание EQP-103


























































Результаты поиска

Содержание EQP-103

Отзывы:

Похожие инструкции для EQP-103

Бренды по названию

Популярные бренды

PlusQuip EQP-103, Руководство пользователя

Результаты поиска

Содержание EQP-103

Отзывы:

Похожие инструкции для EQP-103

Бренды по названию

Популярные бренды