PlusQuip EQP-103 Скачать руководство пользователя страница 25

Страница: 25 / 57

5. OBDII / EOBD Diagnosis

DDiiaaggnnoossttiicc M

Meennuu

allows you to:

•

Read DTCs.

•

Clear DTCs.

•

View live datastream.

•

View freeze data.

•

View I/M Readiness data.

•

O2 sensor test information.

•

View on-board monitor test results.

•

Perform component tests.

•

Retrieve vehicle information.

•

Read modules ID and protocol information.

√√

The code reader detects the communication protocol when it is

connected to the vehicle and uses the protocol throughout the

testing till another vehicle is diagnosed.

√√

If the code reader fails to communicate with the vehicle a

“Communication Error!” message displays. Make sure the OBDII

connector is securely attached, and the ignition key is on. Turn

vehicle key to off for 10 seconds, then on. If problem still exists,

refer to “Error Messages” on page 55 of Troubleshooting.

√√

When the code reader links to vehicle, it checks the status of I/M

Monitors, and gives a summary report on the display as

illustrated below.

EQP-103 User’s Manual

Содержание EQP-103


























































Результаты поиска

Содержание EQP-103

Отзывы:

Похожие инструкции для EQP-103

Бренды по названию

Популярные бренды

PlusQuip EQP-103, Руководство пользователя

Результаты поиска

Содержание EQP-103

Отзывы:

Похожие инструкции для EQP-103

Бренды по названию

Популярные бренды