PLAYSTAR LEGACY PS 73161 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 44

background image

41

SLIDE – Mounting Instructions

SCOOP SlIDe - PS 8816

1. Align Slide at right angle (90˚) to 60" play deck.

Lip of Slide should rest on the play deck 1

¹₂

".

Using the Slide as a template, mark play deck
through the three holes in the Slide. Drill three

¹

/

₈

" holes at marked location.

2. Attach Slide temporarily to play deck with three

#14 x 1

¹

/

₄

" screws provided.

3. Prepare level area where Slide touches ground

that is 1" below surrounding grade.

4. Locate and mark the ground on the back side,

on either side of the star. Remove Slide and
screw Playset Anchor into the ground (a long
screwdriver will help). Screw the anchor deep
enough so that the loop at the top of the anchor
will be flat against the back surface of Slide
when the Slide is in the final position.

5. Reinstall Slide permanently, attaching it to play

deck using #14 x 1

¹

/

₄

" pan head screws

provided.

6. Use the Playset Anchor as a drill guide and drill

a

³₈

" hole completely through the slide. Attach

Slide to anchor with one

³₈

" x 1

¹⁄₄

" hex bolt, two

³₈

" washers and one

³₈

" lock nut provided in the

anchor kit.

7. Fill in around bottom of Slide to make surface

level to surrounding grade.

Caution: Failure to anchor the Slide

properly could cause serious

injury from children lifting the

slide.

Caution: Do not install this Slide over

concrete, asphalt, packed earth,

or any other hard surface. A fall

onto a hard surface can result

in serious injury to the

equipment user.

1"

1"

1¹₂

"

Use the installation instructions

and mounting hardware

supplied with this component.

SPIRAl TuBe SlIDe - PS 8821

«
...
39
40
41
42
43
...
»

Содержание LEGACY PS 73161













































Отзывы:

Нет отзывов

Похожие инструкции для LEGACY PS 73161

Бренд: FENDT Страницы: 31

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: FEBER Страницы: 2

Бренд: FASTERHOLT Страницы: 96

Бренд: Hakko Electronics Страницы: 8

Бренд: Hainbuch Страницы: 52

Бренд: Backyard Play Systems Страницы: 73

Бренд: Trigano Страницы: 4

Бренд: STARPLAY Страницы: 12

Бренд: MacDon Страницы: 558

Бренд: Monosem Страницы: 104

Бренд: Beta Страницы: 8

Бренд: Cutler-Hammer Страницы: 45

Бренд: KUHN Страницы: 92

Бренд: Kaya Safety Страницы: 5

Бренд: Expolite Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды