Playnation Redbrook with Monkey Bars 382 Скачать руководство пользователя страница 85

Страница: 85 / 111

CLIMBING IF

IN THE ROPE

TO AID IN

YOU WISH.

YOU MAY TIE

TWO KNOTS

TIE A KNOT BEHIND

THIS HOLE IN THE

ROCK WALL SIDE

TOP PANEL BOARD

STEP 45: CLIMBING ROPE

1: THREAD ONE END OF THE ROPE THROUGH THE HOLE IN THE ROCK WALL SIDE TOP PANEL

BOARD.
2: TIE A SECURE KNOT ON THE INSIDE OF THE ROCK WALL SIDE TOP PANEL BOARD.
3: THREAD THE OTHER END OF THE ROPE THROUGH THE HOLE IN THE BOTTOM ROCK WALL

BOARD. PULL THE ROPE TIGHT AND TIE A SECURE KNOT BEHIND THE BOTTOM ROCK WALL

BOARD.
4: NOTE: YOU MAY TIE TWO KNOTS IN THE ROPE TO AID IN CLIMBING IF YOU WISH. DO THIS

BEFORE PERFORMING SUB STEP 3.
5: ONCE THE ROPE IS TIED ON BOTH ENDS ATTEMPT TO WRAP THE ROPE AROUND YOUR HANDS.

IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO LOOSE. UN

TIE

ONE END AND RETIE THE

ROPE UNTIL YOU CAN NO LONGER WRA

IT AROUND YOUR HAND.

Содержание Redbrook with Monkey Bars 382
















































































































Результаты поиска

Содержание Redbrook with Monkey Bars 382

Отзывы:

Похожие инструкции для Redbrook with Monkey Bars 382

Бренды по названию

Популярные бренды

Playnation Redbrook with Monkey Bars 382, Руководство пользователя

Результаты поиска

Содержание Redbrook with Monkey Bars 382

Отзывы:

Похожие инструкции для Redbrook with Monkey Bars 382

Бренды по названию

Популярные бренды