Playnation Redbrook with Monkey Bars 382 Скачать руководство пользователя страница 5

Страница: 5 / 111

IMPORTANT SAFETY GUIDELINES

This product is recommended for use by children ages 3-11. This product is intended for residential

use only and not intended for use in any public setting. A safety surface such as mulch or recycled

tire should be used under the play set to prevent injury from falls. Also a 6 foot safety zone should be

used around the entire play set.

As with any home project, good judgment and respect for power tools will greatly reduce the risk

of injury. PlayNation recommends you follow all tool manufacturers’ safety guidelines. Always wear

eye protection and safety gloves to prevent injury. In several phases of construction two people may

be required for lifting and securing of lumber. While the play set is being constructed, please keep

children off the equipment until the project is complete. Bolts and screw heads should be checked

regularly for tightness. The ground ladder, rope ladder, slide, swings and other areas where children

spend a majority of their playtime should be checked more frequently.

PlayNation shall not be liable for incidental, indirect or consequential damages or injuries that result

from the building and/or playing on our play sets. Adult supervision is recommended anytime a play

set is being used.

WEIGHT LIMITS FOR PLAYNATION PLAYSETS

• FORT PLATFORMS: 800 LBS. TOTAL WEIGHT

• SWING BELT: 225 LBS.

• TANDEM SWINGS: 70 LBS. PER CHILD. UP TO 140 LBS TOTAL WEIGHT.

• TRAPEZE: 125 LBS.

• FULL BUCKET SWING/ HALF BUCKET SWING: 50 LBS.

• HEAVY DUTY TODDLER BUCKET SWING: 85 LBS.

• INFANT SWING: 35 LBS.

• TIRE SWING: 125 LBS. TOTAL WEIGHT

• ROPE LADDER: 75 LBS.

• ROCK WALL: 150 LBS.

• CLIMBING RAMP: 150 LBS.

• MONKEY BARS: 175 LBS.

• ALL SLIDES: 150 LBS.

PlayNation recommends that the weight limits for all components must not be exceeded. Failure to

adhere to these and other safety guidelines could result in damage to the play set and injury to the

users.

Содержание Redbrook with Monkey Bars 382
















































































































Результаты поиска

Содержание Redbrook with Monkey Bars 382

Отзывы:

Похожие инструкции для Redbrook with Monkey Bars 382

Бренды по названию

Популярные бренды

Playnation Redbrook with Monkey Bars 382, Руководство пользователя

Результаты поиска

Содержание Redbrook with Monkey Bars 382

Отзывы:

Похожие инструкции для Redbrook with Monkey Bars 382

Бренды по названию

Популярные бренды