Playnation Redbrook with Monkey Bars 382 Скачать руководство пользователя страница 48

Страница: 48 / 111

5/16"

WASHER

2 X 4 X 48"

T-NUT

FORT SUPPORT

5/16" X 2-1/2" HEX BOLT

5/16" WASHER

T-NUT

2 X 4 X 48"

FORT SUPPORT

5/16" X 2-1/2"

HEX BOLT

STEP 8: FORT SUPPORTS

1: PLACE A 5/16" T-NUT INTO THE HOLE IN THE FORT SUPPORTS AS SHOWN.
2: FROM THE INSIDE OF THE RIGHT PANEL BOARD LOOSELY ATTACH EACH FORT SUPPORT WITH

ONE 5/16" X 2-1/2" HEX BOLT AND ONE 5/16" WASHER.
3: MEASURE 2" AND 3-1/2" DOWN FROM THE TIP OF EACH FORT SUPPORT AND DRILL A 1/8"

HOLE THROUGH THE FORT SUPPORT ALONG THE CENTER. (SEE DETAIL A)
4: PLACE EACH FORT SUPPORT AGAINST THE CORNER POST. THE SIDE OF THE FORT SUPPORT

SHOULD BE FLUSH WITH THE RIGHT SIDE OF THE RIGHT CORNER POSTS.
5: ATTACH THE ANGLED END OF EACH FORT SUPPORT WITH ONE 2-1/2" WOOD SCREW AND

ONE 3" WOOD SCREW. TIGHTEN EACH 5/16" X 2-1/2" HEX BOLT.

WOOD

SCREW

DETAIL A

SCALE 1 : 9

2-1/2"

WOOD

SCREW

2" 3

2 "

Содержание Redbrook with Monkey Bars 382
















































































































Результаты поиска

Содержание Redbrook with Monkey Bars 382

Отзывы:

Похожие инструкции для Redbrook with Monkey Bars 382

Бренды по названию

Популярные бренды

Playnation Redbrook with Monkey Bars 382, Руководство пользователя

Результаты поиска

Содержание Redbrook with Monkey Bars 382

Отзывы:

Похожие инструкции для Redbrook with Monkey Bars 382

Бренды по названию

Популярные бренды