Platinum Z5 CD Скачать руководство пользователя | Manualshive

Страница: 7 / 194

background image

2

408

ti.f

m

888-2408-002

WARNING: Disconnect primary power prior to servicing.

WARNING

The currents and voltages in this equipment are dangerous. Person-
nel must at all times observe safety warnings, instructions and regu-
lations.

This manual is intended as a general guide for trained and qualified personnel who are
aware of the dangers inherent in handling potentially hazardous electrical/electronic
circuits. It is not intended to contain a complete statement of all safety precautions which
should be observed by personnel in using this or other electronic equipment.

The installation, operation, maintenance and service of this equipment involves risks both
to personnel and equipment, and must be performed only by qualified personnel exercising
due care. HARRIS CORPORATION shall not be responsible for injury or damage
resulting from improper procedures or from the use of improperly trained or inexperienced
personnel performing such tasks.

During installation and operation of this equipment, local building codes and fire protec-
tion standards must be observed. The following National Fire Protection Association
(NFPA) standards are recommended as reference:

• Automatic Fire Detectors, No. 72E

• Installation, Maintenance, and Use of Portable Fire Extinguishers, No. 10

• Halogenated Fire Extinguishing Agent Systems, No. 12A

WARNING

Always disconnect power before opening covers, doors, enclosures,
gates, panels or shields. Always use grounding sticks and short out
high voltage points before servicing. Never make internal adjust-
ments, perform maintenance or service when alone or when fa-
tigued.

Do not remove, short-circuit or tamper with interlock switches on access covers, doors,
enclosures, gates, panels or shields. Keep away from live circuits, know your equipment
and don’t take chances.

WARNING

In case of emergency ensure that power has been disconnected.

If oil filled or electrolytic capacitors are utilized in your equipment, and if a leak or bulge
is apparent on the capacitor case when the unit is opened for service or maintenance, allow
the unit to cool down before attempting to remove the defective capacitor. Do not attempt
to service a defective capacitor while it is hot due to the possibility of a case rupture and
subsequent injury.

«
...
5
6
7
8
9
...
»

Содержание Z5 CD



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z5 CD

Бренд: Nautel Страницы: 224

Бренд: Hama Страницы: 24

Бренд: Alinko Страницы: 48

Бренд: Icom Страницы: 116

Бренд: National Instruments Страницы: 43

Бренд: Warner RF Страницы: 7

Бренд: Labom Страницы: 3

Impresario Chronis io

Бренд: SOMFY Страницы: 74

Бренд: Kubu, inc. Страницы: 6

Бренд: Icom Страницы: 47

DeepSEE DS 10 -1.5

Бренд: Ulthera Страницы: 72

Бренд: Abilia Страницы: 16

Бренд: Icom Страницы: 2

Бренд: Standard Communications Страницы: 20

Бренд: SSS Siedle Страницы: 32

Бренд: Super Star Страницы: 10

Бренд: Industrial Controls Страницы: 5

Бренд: FOS Technologies Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды