Plasma IBEAM FC Скачать руководство пользователя страница 28

Страница: 28 / 60

The options for each module in the main display will utilize abbreviations. The following is a listing

of these abbreviations, the corresponding parameter and description. The specific module and

acceptable range are also provided. Consult the source check-out sheet for typical values.

MODULE ABBREVIATION PARAMETER AND DESCRIPTION

ACCEPTABLE
RANGE

Beam

BEAM V or

Beam voltage

After the beam is turned on, the power
supply will ramp to the beam voltage.

0 to 1500 V

Beam

Beam current

After the beam is turned on, the power
supply will ramp the beam current.

0 to 300 mA

Accelerator ACCEL

Accelerator voltage

Below 100 V is not recommended.

0 to 1000 V

Discharge

DISC V

Discharge voltage

Typical values are 35 to 55 V.

0 to 80 V

Cathode

CATH I

Cathode filament current

0.0 to 20.0 A

Neutralizer NEUT I

Neutralizer filament current

0.0 to 20.0 A

Control

SETUP

Select to change global parameters listed
below

Control

CATH I LIMIT

Cathode filament current limit

The limit should be set slightly higher than
the maximum expected cathode filament

current.

0.0 to 20.0 A

Control

NEUT I LIMIT

Neutralizer filament current limit

The limit should be set slightly higher than
the maximum expected neutralizer filament

current

0.0 to 20.0 A

Control

A/B RATIO

Accelerator to beam current ratio

If the accelerator current exceeds the A/B

ratio times the beam current, an alarm is
triggered. Default is 10%.

0 to 99%

Control

E/B RATIO

Emission to beam current ratio

Neutralizer emission will ramp to the E/B

ratio times beam current. Recommended is
125%.

0 to 200%

Control

RMT S/B SW

Remote source / beam switch

This will activate the rear panel remote
switch (see Chapter 5).

enable/disable

Control

ALARM

Audio alarm

enable/disable

Control

SECURITY

Factory use

MEM key

STORE

Store beam parameters into memory

0 to 9

MEM key

RECALL

Recall beam parameters from memory

0 to 9

All

INC

Increase value by 1 or 0.1

All

DEC

Decrease value by 1 or 0.1

Содержание IBEAM FC





























































Результаты поиска

Содержание IBEAM FC

Отзывы:

Plasma IBEAM FC, Руководство пользователя, Страница: 28 / 60

Результаты поиска

Содержание IBEAM FC

Отзывы: