background image

Table of Contents

 

1. INTRODUCTION ................................................................................................................... 4

 

1.1 Packet Contents .............................................................................................................. 4 

1.2 How to Use This Manual ................................................................................................. 4 

1.3 Product Feature............................................................................................................... 4 

1.4 Product Specification....................................................................................................... 5 

2. INSTALLATION..................................................................................................................... 7

 

2.1 Product Description......................................................................................................... 7 

2.2 Mounting Installation ......................................................................................................11 

3. Hardware Installation ........................................................................................................ 14

 

4. TROUBLESHOOTING ........................................................................................................ 16

 

4.1 Incorrect connections .................................................................................................... 16 

4.2 Diagnosing LED Indicators............................................................................................ 16 

Appendix A Networking Connection ................................................................................... 18

 

A.1 Switch‘s RJ-45 Pin Assignments .................................................................................. 18 

A.2 RJ-45 cable pin assignment ......................................................................................... 18 

 

Содержание IFT-802



















Отзывы: