background image

#

Notice:  

The Fiber port has single-mode and multi-mode. To check your Industrial media converter fiber connector 

type, look for the sticker on the Industrial media converter. 

The 

multi-mode

 connector type must use 50 or 62.5/125 µm multi-mode fiber cable. The connect 

distance between two devices is up to 

2Km

Step6:

 Insert one side of Category 5 cables into the Industrial media converter Ethernet port (RJ-45 port) 

and another side of category 5 cables to the network switch's Ethernet port (RJ-45 port). The UTP port 

(RJ-45) LED on the Industrial media converter will light up when the cable connected with the switch. 

Please refer to the 

LED Indicators

 section for LED light meaning. 

#

Notice:  

Be sure the connected local switch's Ethernet port support MDI/MDI-X. If it does not support then use the 

crossover category 5 Cable. 

Step7: 

Insert one side of fiber cable into the Industrial media converter fiber port and another side to the 

convert in the opposite side connection. The fiber port LED on the converter will light up when the cable 

connected. Please refer to the 

LED Indicators

 section for LED light meaning. 

Step8:

 When all connections are all set and LED lights all show in normal, the installation is complete. 

 

 

Содержание IFT-802



















Отзывы: