Planar 2D-12 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

background image

28

3.9.6 Heater Electrical Wiring Installation.

Installation of wire harnesses and other electrical parts of

the heater should be made according to the wiring diagram.
Install the harnesses so as to prevent their heating, deformation,
and movement during vehicle operation. Fix the harness with
plastic collars to vehicle parts.

Attention! Mounting shall be carried out with the fuse

removed.

If the length of the fuel pump wiring harness needs
to be shortened, it is allowed to remove an
unnecessary portion from the middle of the
harness. The splice should be insulated.

Installation of the fuel pump electrical harness connector is

shown in Fig.31.

«
...
26
27
28
29
30
...
»

Содержание 2D-12





































Отзывы:

Нет отзывов

Похожие инструкции для 2D-12

Бренд: A.O. Smith Страницы: 64

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 4

120 through 250 Series

Бренд: A.O. Smith Страницы: 74

Бренд: Cabletron Systems Страницы: 30

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 24

Бренд: GALAXY SPAS Страницы: 26

Бренд: Kambrook Страницы: 6

Бренд: Zibro Страницы: 64

Бренд: Daewoo Страницы: 18

Бренд: Phillips & Temro industries Страницы: 3

Бренд: EUROM Страницы: 120

Бренд: ESBE Страницы: 28

Rocco FBFL**RN3

Бренд: Flavel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды