Pitney Bowes relay 2000 Скачать руководство пользователя страница 85

Страница: 85 / 92

Material Specifications • 7

7-3

SV63139 Rev. A

Material Specifications

Sheet Feeders

Minimum Sheet Size:

5 inches (127mm) width

5 inches (127mm) length

Maximum Sheet Size:

9 inches (229mm) width

16 inches (406mm) length

Paper Weights:

16 lb. (60gsm) (minimum, non-OMR)

18 lb. (70gsm) (minimum, OMR)

32 lb. (120gsm) (maximum)

Fold Configurations (

material length limits before folding):

Fold Type

Measurement

Single fold

5 inches (127mm) - 12 inches (315mm)

C (letter fold)

6 inches (150mm) - 14 inches (356mm)

Z (accordion fold) 8 inches (201mm) - 14 inches (356mm)

Double fold

12 inches (305mm) - 16 inches (406mm)

Double Document Detector Material Range:

Minimum: 16 lb (60gsm)
Maximum: 32 lb (120gsm)

Feed Tray Capacity:

maximum of 325 sheets of 20 lb. bond (80gsm)

Manual Feed Mode:

• Inserter processes stapled sets of up to five sheets of 20 lb. bond

(80gsm) up to a maximum total weight of 100 lbs. (400gsm) per set.

NOTE: For manual feed applications, you may use only sheet feeder

number 1, plus the insert feeder if required.

• Maximum compressed thickness after folding

must not

exceed

0.078 inch (2mm).

• We

do not

recommend the use of glossy/coated sheets.

IMPORTANT: All specifications are subject to change without notification

and are subject to test.

Содержание relay 2000




























































































Результаты поиска

Содержание relay 2000

Отзывы:

Похожие инструкции для relay 2000

Бренды по названию

Популярные бренды

Pitney Bowes relay 2000, Руководство оператора

Результаты поиска

Содержание relay 2000

Отзывы:

Похожие инструкции для relay 2000

Бренды по названию

Популярные бренды