Pitney Bowes Epic v3.1 Скачать руководство пользователя страница 164

Страница: 164 / 336

4. Place an insert from the job under the double detect roller.

5. With the insert under the roller, loosen both double detect bracket screws and lower the assembly

so the double detect roller touches the insert.

6. Next, keep the bracket square and tighten the two bracket screws.

7. Now, place two inserts under the double detect roller. The light on the left side of the feeder should

illuminate.

(NOTE: If the light does not illuminate, turn the double detect adjustment knob

counterclockwise until it comes on.)

8. Remove the two inserts, and the light should turn off.

9. Place a single insert under the double detect roller and the light should stay off.

Note:

If the light does not go off, try repeating steps 7 and 8.

10. To check the adjustment, remove the single insert and put two inserts back under the roller, the

light should turn on.

Operator Adjustments

Pitney Bowes

Epic v3.1 (ZVE0) Operator Guide

May, 2018

Page 157 of 328

Содержание Epic v3.1
















































































































































































































































































































































Результаты поиска

Содержание Epic v3.1

Отзывы:

Похожие инструкции для Epic v3.1

Бренды по названию

Популярные бренды

Pitney Bowes Epic v3.1, Руководство оператора

Результаты поиска

Содержание Epic v3.1

Отзывы:

Похожие инструкции для Epic v3.1

Бренды по названию

Популярные бренды