manualshive.com logo in svg

Piscine Solide V35048, Руководство по установке, Страница: 41 / 49

Поделиться
Скачать
Piscine Solide V35048 Скачать руководство пользователя страница 41

No Diving or Jumping.  Observe all Safety Rules

GENERAL INSTRUCTIONS - ROUND POOLS

ASSEMBLING THE POOL FRAME

Section

4

1. Finish filling the pool

a.  Turn off the vacuum and carefully remove it from the 

pool.

b.  Fill the pool with water to 2” (5cm) below the lowest 

opening. 

c.  While the pool is filling, remove the nails that were 

holding the bottom rails in place and ensure that they are 
still positioned correctly.

d.  Your pool is now installed. You must now install the filter 

and pump, the skimmer and water return inlet.Please 
follow the installation instructions that come with these 
products.

 

D. FILL YOUR POOL WITH WATER

Important Note:

Before making any openings in the liner, fill the pool with 60cm 
(24”) of water to stretch the liner fully. When filling your pool, 
begin  with  a  garden  hose  until  there  is  about  30cm  (12”)  of 
water in the pool. This will allow the liner to stretch gradually. 
You can then use a heavier flow to finish filling it up.

4-7

Important Note:

Make sure that your pool’s round sections are round, do not assume that by filling up the pool that this will help the pool 
to place itself into a perfect round shape. Ensure that it is round before filling up the pool with water.

Содержание V35048


















































Отзывы:

Нет отзывов