Additional information
14
87
En
Remote control
HDMI
Symptom
Remedy
Cannot be remote controlled.
• Try replacing the batteries in the remote control (see
Loading the batteries
on page 6).
• Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see
Operating range
of remote control unit
on page 24).
• Check that there are no obstacles between the receiver and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the
CONTROL IN
jack (see
Operating other Pioneer components with this unit’s
sensor
on page 81).
Other components can’t be
operated with the system remote.
• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
The SR cable is connected, but
the connected components can’t
be operated with the remote.
• Reinsert the SR cable, making sure it’s connected to the right jack (see
Using this receiver with a Pioneer
plasma display
on page 61).
• Make sure that there is an analog or HDMI connection between the units. This is necessary for the SR
feature to work.
• Check that the other component is made by Pioneer. The SR feature only works with Pioneer equipment.
Symptom
Remedy
The HDMI indicator blinks
continuously.
• Check all the points below.
No picture or sound.
• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component, S-video or composite video jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver (even
if it is HDCP-compatible). In this case, connect using the component, S-video or composite video jacks
between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV or plasma display, try adjusting the resolution, DeepColor or
other setting for your component.
• If ‘
NOT SUPPORT
’ appears in the receiver’s display, try adjusting the resolution, DeepColor or other
setting for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio output.
• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to THROUGH, you
cannot hear audio output from all channels. In this case, make a digital or analog audio connection.
• To output signals in DeepColor, use an HDMI cable (compliant with Version 1.3a, Category 2) to connect
this receiver to a component or TV with the DeepColor feature.
No picture.
• Try changing the Resolution setting (in
Setting the Video options
on page 71).
No sound, or sound suddenly
ceases.
• Check that the HDMI AV setting is set to
AMP/THROUGH
.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection for the audio.
• Check the audio output settings of the source component.
Noisy or distorted picture.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-video or composite), then start playback again.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
HDCP ERROR
shows in the
display.
• Check whether or not the connected component is compatible with HDCP. If it is not compatible with
HDCP, reconnect the source device using a different type of connection (component, S-video or composite).
Some components that are compatible with HDCP still cause this message to be displayed, but so long as
there is no problem with displaying video, this is not a malfunction.
VSX_LX60LX70.book Page 87 Wednesday, June 6, 2007 3:13 PM
