Pioneer VSX-LX60 Скачать руководство пользователя страница 44

Страница: 44 / 99

The System Setup menu

Fine Speaker Distance

• Default setting:

3.00 m

(all speakers)

For proper sound depth and separation with your system,
it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening
position at the same time. The following setting can help
you make detailed adjustments that you may not achieve
using the

Manual speaker setup

below.

Select ‘Fine SP Distance’ from the Manual MCACC

setup menu.

Adjust the distance of the left channel from the

listening position.

Select each channel in turn and adjust the distance

as necessary.

Use

/

to adjust the delay of the speaker you selected

to match the reference speaker. The delay is measured in
terms of speaker distance from

0.01

9.00

meters.

Listen to the reference speaker and use it to measure the
target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each
speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of

you and between your arm span.

When it sounds like the delay settings are matched up,
press



to confirm and continue to the next channel.

• For comparison purposes, the reference speaker will

change depending on which speaker you select.

• If you want to go back and adjust a channel, simply

use

/

to select it.

When you’re finished, press RETURN.

You will return to the Manual MCACC setup menu.

Standing Wave

• Default setting:

Acoustic standing waves occur when, under certain
conditions, sound waves from your speaker system
resonate mutually with sound waves reflected off the
walls in your listening area. This can have a negative
effect on the overall sound, especially at certain lower
frequencies. Depending on speaker placement, your
listening position, and ultimately the shape of your room,
it results in an overly resonant (‘boomy’) sound. The
Standing Wave Control uses filters to reduce the effect of
overly resonant sounds in your listening area. During
playback of a source, you can customize the filters used
for Standing Wave Control for each of your MCACC

presets.

Select ‘Standing Wave’ from the Manual MCACC

setup menu.

Select ‘ON’ (if it is not already selected) then adjust

the parameters for the Standing Wave Control.

•

Filter Ch

– Select the channel to which you will apply

the filter(s):

Main

(all except center channel and

subwoofer),

Center

(subwoofer).

•

TRIM

(only available when the filter channel above is

)

– Adjust the subwoofer channel level (to

compensate for the difference in output post-filter).

•

ATT

– These are the filter parameters where

represents the frequency you will be targeting and

is the bandwidth (the higher the Q, the narrower the
bandwidth, or range) of the attenuation (

ATT

, the

amount of reduction to the targeted frequency).

When you’re finished, press RETURN.

You will return to the Manual MCACC setup menu.

Note

1 • If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your speakers very slightly.

• For better audibility, the subwoofer emits a continuous test tone (oscillating pulses are heard from your other speakers). Note that it may be difficult to

compare this tone with the other speakers in your setup (depending on the low frequency response of the reference speaker).

: R e t u r n

a . F i n e C h a n n e l L ev e l

b . F i n e S P D i s t a n c e

c .  S t a n d i n g  Wav e
d .  E Q   A d j u s t
e .  E Q   P ro fe s s i o n a l

3 . M a nu a l M C AC C

DV D / L D

- 5 5 . 0 dB

M C AC C : M 1 . M E M O RY 1

R e f. C h : L

3 . 0 0 m

E N T E R : N ex t