Pioneer VSX-933 Скачать руководство пользователя страница 18

Страница: 18 / 131

≫

≫

≫

≫

≫

≫

❏

Ceiling Speakers Installation Example

*1: 30° to 55°, *2: 65° to 100°, *3: 125° to 150°

This is a system with the basic 5.1 channel system (

p14

) consisting of front

speakers, a center speaker, surround speakers and a powered subwoofer, and

added top front speakers or top middle speakers or top rear speakers combined.

By installing such height speakers, when the input format is Dolby Atmos, you

can select the Dolby Atmos listening mode which realizes the most up-to-date

3D sound including overhead sound. Install the top front speakers on the ceiling

anterior to the seating position, top middle speakers on the ceiling directly above

the seating position, and top rear speakers on the ceiling posterior to the seating

position. The distance between each pair should match the distance between the

front speakers.

• Dolby Laboratories recommends the setups of these types of height speakers

to obtain the best Dolby Atmos effect.

7,8 Height Speakers

Choose one of the following:

• Top Front Speakers

• Top Middle Speakers

• Top Rear Speakers

Содержание VSX-933




































































































































Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды

Pioneer VSX-933, Инструкция по эксплуатации

Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды