Pioneer VSX-933 Скачать руководство пользователя страница 10

Страница: 10 / 131

≫

≫

≫

≫

≫

≫

DIGITAL AUDIO IN OPTICAL/COAXIAL jacks: Input TV or AV component

digital audio signals with a digital optical cable or digital coaxial cable.

ANTENNA AM LOOP/FM UNBAL 75Ω terminal: The supplied antennas are

connected.

VIDEO IN jacks: Input the AV component video signals with an analog video

cable.

USB port: A USB storage device is connected so that music files stored in it

can be played. (

p49

) You can also supply power (5 V/500 mA) to USB

devices with a USB cable.

COMPONENT VIDEO IN jacks: Input the AV component video signals with a

component video cable. (Compatible only with 480i or 576i resolution.)

NETWORK port: Connect to the network with a LAN cable.

Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTH

enabled device. Adjust their angles according to the connection status.

HDMI OUT jacks: Transmit video signals and audio signals with a HDMI cable

connected to a TV.

HDMI IN jacks: Transmit video signals and audio signals with a HDMI cable

connected to an AV component.

10. Power cord

11.

SIGNAL GND terminal: The ground wire of the turntable is connected.

12.

AUDIO IN jacks: Input AV component audio signal with an analog audio cable.

13.

SPEAKERS terminals: Connect speakers with speaker cables. (North

American models support banana plugs.)

14.

ZONE 2 LINE OUT jacks: Output audio signals with an analog audio cable

connected to a pre-main amplifier in a separate room (ZONE 2).

15.

SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a

subwoofer cable. Up to two powered subwoofers can be connected. The same

signal is output from each of the SUBWOOFER PRE OUT jacks.

Содержание VSX-933




































































































































Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды

Pioneer VSX-933, Инструкция по эксплуатации

Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды