Pioneer VSX-933 Скачать руководство пользователя страница 115

Страница: 115 / 131

115

Troubleshooting

≫

≫

≫

≫

≫

≫

Troubleshooting

Before starting the procedure

Problems may be solved by simply turning the power on/off or disconnecting/

connecting the power cord, which is easier than working on the connection,

setting and operating procedure. Try the simple measures on both the unit and

the connected device. If the problem is that the video or audio is not output or the

HDMI linked operation does not work, disconnecting/connecting the HDMI cable

may solve it. When reconnecting, be careful not to wind the HDMI cable since

if wound the HDMI cable may not fit well. After reconnecting, turn off and on the

unit and the connected device.

• The AV receiver contains a microPC for signal processing and control

functions. In very rare situations, severe interference, noise from an external

source, or static electricity may cause it to lockup. In the unlikely event

that this happens, unplug the power cord from the wall outlet, wait at least

5 seconds, and then plug it back in.

•

Onkyo is not responsible for damages (such as CD rental fees) due to

unsuccessful recordings caused by the unit’s malfunction. Before you record

important data, make sure that the material will be recorded correctly.

When the unit is operating erratically

116

Try restarting the unit

116

Resetting the unit

(this resets the unit settings to the default)

116

Troubleshooting 117

Multi-zone function (for compatible models only) 124

Содержание VSX-933




































































































































Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды

Pioneer VSX-933, Инструкция по эксплуатации

Результаты поиска

Содержание VSX-933

Отзывы:

Похожие инструкции для VSX-933

Бренды по названию

Популярные бренды