Pioneer KFDH100 Скачать руководство пользователя страница 10

Controller Operation

8

 IR reception

 

System receives commands from handset.

9

 Cool mode

 

In Cool mode, compressor will cut in if Tr - Ts >= 0.5°C and cut out if Tr - Ts =< (-1.0)°C,

 

subject to 3 minutes protections and minimum run time. Indoor fan speed can be manually

 

selected or determine by the system in Auto Fan speed according to the return air temp.

 10

 Dry mode

 

Indoor fan runs at low speed.

 

Compressor will cut out if:-

 

 

a) It has run for 10 minutes continuously or

 

 

b) Tr - Ts =< (-1.0)°C

 

It is then allow to cut in if:-

 

 

a) It has stop for 5 minutes and

 

 

b) Tr - Ts >= 0.5°C

11

 Fan mode

  

Only High, Medium and Low speed selection is allowed (KFDH075,100 only) .

12

 Error code

If multiple faults happen at the same time, the corresponding error code will be shown one after another.

13

 Off mode

 

All output are off during system off state except indoor fan which are subject to the

minimum operating time guard where applicable.

6

Compressor protection

 

a) Comp restart protection

 

1. 3 minutes protection

 

2. Hardware Anti short cycle timer

 

    Should the power supply is cut off and resume, compressor 3 minutes

 

    protection control logic is as below:-

7

Temperature sensor fault

 

a) Return air sensor

 

     Monitor continuously

 

b) Indoor coil sensor

 

•  If comp is turned on, monitoring is done 5 minutes after comp running. 

  

•   If comp is stop, monitor continuously

 

Upon happening of any sensor fault, system is forced to Fan mode. It will then resume

 

to normal mode upon clearance of fault.

 

b) 90S minimum run time (compressor)

 

c) Indoor coil anti freeze

Power outage duration   Restart protection timer

<180S 

180S— 243S 

>180S

< 63S 

Fault 

Error code

Room sensor fault 

E1 

 

Indoor coil sensor fault  E2 

 

Comp fault 

E4 

 

9

Содержание KFDH100

















Отзывы: