21
HTP-SB300
5
6
7
8
5
6
7
8
A
B
C
D
E
F
5.2 DESCRIPTION OF WIRELESS PAIRING OPERATIONS
Descriptions of Wireless Modes
1. Factory Mode
• Factory-set initial status
• The LED indications are as follows:
• To enter Factory Mode
TX (Sound Bar block)
1. Set TX to Power ON status then press the MUTE Key on
the remote control while holding the STEREO Key on
the main unit pressed.
2. The FL display shows “FACTORY MODE.”
3. The red and green LEDs blink alternately at intervals of
500
ms.
RX (Subwoofer block)
1. Operate TX and RX in Normal Mode.
2. When you set TX to Factory Mode from the state of 1
above, RX also automatically enters Factory Mode.
• How to shift from Factory Mode to Normal Mode
1. After Factory Mode is entered, once turn the power off
(setting TX to Standby status and RX to AC OFF status).
2. When you turn TX and RX back on, they enter Auto
Pairing Mode then shift to Normal Mode after several
seconds.
2. Normal Mode
• Normal operation status
• The LED indications are as follows:
• This mode can be entered in the following conditions:
1. When TX and RX are turned on in Factory Mode (The ID
of RX is changed to that of TX.)
2. When TX and RX are turned on with the same ID.
• This mode can be entered in the following conditions:
1. When only TX is in Power ON status while RX is in
Power OFF status
2. When only RX is in Power ON status while TX is in
Standby
status
3. When TX and RX differ in ID although both are in Power
ON
status
• Status where TX and RX are searching for each other
• The LED indications are as follows:
4. Re-Pairing (Manual Pairing) Mode
• Mode to normally operate TX and RX differing in ID.
(Use this mode if any module replacement has
occurred in servicing, etc.)
• The LED indications are as follows:
• To enter the mode
TX (Sound Bar block)
1. With TX in Power ON status, simultaneously press the
SHIFT key and the CH- key for TV CONTROL on the
remote
control.
2. The green LED blinks at intervals of 250 ms.
RX (Subwoofer block)
1. RX starts Re-Pairing operation upon power on and
continues it for 15 seconds at maximum. The method of
Pairing with TX is as follows:
2. After the above-mentioned TX enters Re-Pairing Mode
(green LED blinking) with the Power Cord of RX
disconnected, connect the AC power to RX.
-> If pairing with TX fails: RX enters Standby Mode 15
seconds after it is turned on (red LED ON).
-> When pairing with TX is successful: RX immediately
enters Normal Mode (green LED ON).
• If Re-Pairing is started for TX in Factory Mode
1. The green LED blinks at intervals of 250 ms.
2. Re-Pairing Mode is maintained for 60 seconds at
maximum. The mode changes to Standby Mode after 60
seconds (red LED ON).
500 ms Toggle Blinking
500 ms Toggle Blinking
RED
RX (Sub Woofer)
TX (Sound Bar)
LED COLOR
GREEN
OFF
OFF
ON
ON
RED
RX (Sub Woofer)
TX (Sound Bar)
LED COLOR
GREEN
5. Sleep Mode (Power Save Mode)
• Standby Mode is entered if no audio signal of a
subwoofer channel is sent from TX to RX for 10
minutes.
• The LED indications are as follows:
• If any audio signal of a subwoofer channel is sent to TX
in Sleep Mode, the mode automatically changes to
Normal Play Mode.
ON
ON
OFF
OFF
RED
RX (Sub Woofer)
TX (Sound Bar)
LED COLOR
GREEN
OFF
OFF
500 ms Blink
250 ms Blink
RED
RX (Sub Woofer)
TX (Sound Bar)
LED COLOR
GREEN
ON
OFF
OFF
RX (Sub Woofer)
GREEN
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
