Pioneer CDJ-2000NXS, Руководство по обслуживанию

Страница: 28 / 158

28
CDJ-2000NXS
1 2 3 4
A
B
C
D
E
F
1 2 3 4
1 ————— Traverse mecha Check that focusing is in. (If focusing is
out, tracking close is not possible.) See “In-focus not possible” above. —————
1 ————— Traverse mecha Check the MAI N DSP (IC301,) using
automatic device diagnostics and the
status LEDs.
If it is judged as N G, the ATAPI drive does not
work properly. If the track data are not output
although loading and rotating are properly
performed, see [6] ATAPI DRI
V E. In other cases,
see [9] DRI V E ASSY.
6.1 SER V ICE MODE_
[3] Indication of various
information
1 ————— ————— ————— If it is judged as N G, the MAI N DSP (IC302) does
not work properly or communication between the
MAI
N CPU (IC10) and MAI N DSP is not
established. Proceed as follows:
—————
2 Power is not
supplied properly. MAI N Assy Check the power voltages ( V +3R3_DSP
and V +1R2_DSP).
The MAI N DSP requires two power supply systems.
Check the connections of the power supply lines.
If soldering is improper, resolder it.
—————
3 The clock is not
properly input. MAI N Assy Check that the frequency at Pin 3 8 (DSP_
CLK) of SD_RAM (IC302) is
approx. 129 MHz.
Check the connection of the logic ICs
(IC16, 506).
If soldering is improper, resolder it. —————
4 The RESET
signal is not
properly input. MAI N Assy Check that the signals of the DSP_RST
and CPU_DSP_RST lines are H. Check the connection of the logic IC (IC 8 ).
If soldering is improper, resolder it.
If the signal of the CPU_DSP_RST line is L, the
port on the MAI
N CPU may be damaged.
If the signal of the DSP_RST line is L, check the
connection of the logic IC (IC
8 ) and its periphery.
—————
5 Loose connection
between the MAI
N
CPU and MAI N DSP
MAI N Assy Check the connection between the
MAI
N CPU and MAI N DSP.
Check the connections between MAI N CPU
(IC10) and MAI N DSP (IC301).
If soldering is improper, resolder it.
—————
6 Loose connection
between the MAI
N
DSP and SD_RAM
MAI N Assy Check the connection between the
MAI
N DSP and SD_RAM.
Check the connections between MAI N DSP
(IC301) and SD_RAM (IC302).
If soldering is improper, resolder it.
—————
N o tracking close
2 Signal error SR V B Assy With a CD, check that the E and F signals
fluctuate with 2.2
V at the center.
With a D V D, check the A, B, C, and D
signals.
Check that the signals fluctuate with 2.2 V at the center.
If a DC signal is not output, check the V REF1. If a DC
signal is not output from it, replace the FEP (IC7002).
If an AC signal is not output, check the soldering at the
C
N 7001–IC7002 of the pickup. If soldering is improper,
resolder it. If soldering is OK, replace the traverse
mecha.
5.4 OPERATIO N AL
WA V EFORMS
3 TE signal error SR V B Assy Check that the TE signal fluctuates
with 1.65
V at the center.
Check the connection of the parts at the periphery of
the FEP (IC7002). If soldering is improper, resolder it.
If soldering is OK, replace the FEP (IC7002). 5.4 OPERATIO N AL
WA V EFORMS
4 5 6 7 8
4 TEDR V signal
error
SR V B Assy Check that the TEDR V signal fluctuates
with 1.65 V at the center, and that a
pulselike signal is output during tracking
close.
If the output signal waveform is not proper, the connection
of the SODC (IC7006) and its periphery may be
loose or the parts may be defective. If the connection is
loose, reconnect securely. If the connection is OK,
replace the SODC (IC7006). 5.4 OPERATIO N AL
WA V EFORMS
6 7 8
[12] Error Codes
[12-1] E-7001: DISC DRI V E ERROR
How to respond when an error code is displayed on the CO N TROLLER DISPLAY (LCD) is described below.
The ATAPI drive does not work properly.
[12-2] E-7010: DSP DE V ICE ERROR
The MAI N DSP (IC301) does not work properly. Downloading of programs is not possible.
5 ————— ————— If the symptom persists after the above
corrections. Replace the parts in the order of (1) FEP (IC7002),
(2) SODC (IC7006), (3) DRI
V ER IC (IC7001),
(4) SR V B Assy, then (5) traverse mecha.
—————
7 ————— ————— If the symptom persists after the above
corrections. Replace the MAI N Assy. —————
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference