Pioneer Eclipse PE420BU Скачать руководство пользователя страница 12

Страница: 12 / 68

Unpacking the Machine

The machine is shipped boxed on a wooden pallet. To

unpack machine:

1. Cut and remove bands holding the box to the pallet.
2. Remove staples attaching the box to the platform at

the bottom edge of the box.

3. With two people, one at either end of the box, lift box

straight up and off machine.

4. Cut and remove bands securing the machine to the

pallet.

5. Remove back brace.
6. Remove hex lock nut, bolt, and washer from handle.

7. Rotate handle to the user position to the top of the

adjustment slot. Then insert the bolt through the

handle bracket and handle top.

8. Place the washer and handle adjustment lever on the

bolt. Thread the adjustment lever in until it is against

the handle bracket, but do not tighten.

9. Adjust the handle to the desired height and tighten

the handle adjustment lever.

10. Check machine fluid levels (engine oil). See

Maintenance

section.

NOTE: If machine was shipped by airfreight, add

engine oil.

11. Carefully back the machine off of the pallet.

Filling the LP Cylinder

This machine uses the 20 lb (9.1 kg) capacity cylinder,

which meets the D.O.T. 4E240 standards. These

cylinders are also listed by UL. In addition, the steel

cylinder meets European TPED specifications and

is CE compliant. Filling should be done ONLY by a

qualified propane dealer. A properly filled cylinder

should not exceed 80% of the rated capacity. Do not

overfill the cylinder or use a liquid withdraw cylinder on

the machine. The use of a liquid withdraw cylinder on

a vapor withdraw system could freeze the regulator and

create a fire hazard.

Installing the LP Cylinder

Place the cylinder on the cylinder platform at the back

of the machine. Connect the fuel hose coupling to the

service valve by turning to the right (clockwise). HAND

TIGHTEN ONLY! Make sure coupling is not cross

threaded and check for leakage by noting any propane

odors immediately after cylinder is connected. Finally,

secure the tank to the machine using the adjustable

strap. Remove slack by pulling on the loose end and

securing with the Velcro.

TO REMOVE THE LP CYLINDER

, reverse the above

procedure. Always connect or change cylinders in a

well-ventilated area.

Machine Preparation

Содержание PE420BU





































































Результаты поиска

Содержание PE420BU

Отзывы:

Похожие инструкции для PE420BU

Бренды по названию

Популярные бренды

Pioneer Eclipse PE420BU, Руководство оператора

Результаты поиска

Содержание PE420BU

Отзывы:

Похожие инструкции для PE420BU

Бренды по названию

Популярные бренды