PIONEER DJ DDJ-1000STR Скачать руководство пользователя страница 56

Страница: 56 / 132

Advanced use

Using the Performance Pads

You can switch the functions using the respective pad mode buttons
(the

[HOT CUE]

mode button,

[ROLL]

mode button,

[SLICER]

mode

button and

[SAMPLER]

mode button).

Using Hot Cues

You can start playback instantly from the position where a Hot Cue is
set.

•

Up to 8 Hot Cue points can be set and saved for each track.

1 Press the

[HOT CUE]

mode button.

The unit enters Hot Cue mode.

2 If the track is playing or paused, press a Performance Pad to set the

Hot Cue point.

The Hot Cue points are set to Performance Pads as follows:

3 Press a Performance Pad you’ve set a Hot Cue for.

Playback starts from the Hot Cue point.

•

You can clear Hot Cue points by pressing a Performance Pad while holding
the

[SHIFT]

button.

Hot Cue

Содержание DDJ-1000STR





































































































































Результаты поиска

Содержание DDJ-1000STR

Отзывы:

Похожие инструкции для DDJ-1000STR

Бренды по названию

Популярные бренды

PIONEER DJ DDJ-1000STR, Руководство по эксплуатации

Результаты поиска

Содержание DDJ-1000STR

Отзывы:

Похожие инструкции для DDJ-1000STR

Бренды по названию

Популярные бренды