PIONEER DJ DDJ-1000STR Скачать руководство пользователя страница 104

Страница: 104 / 132

Changing the settings

104

Channel Fader Start setting

Change the setting of the Channel Fader Start feature.
Setting item:

[CH FDR START]

• [ON(SYNC ON)]

The Channel Fader Start feature is enabled with the Sync feature.
(The Sync feature is activated when the Channel Fader Start feature
starts.)

• [ON(SYNC OFF)]

The Channel Fader Start feature is enabled without the Sync feature.
(The Sync feature isn’t activated when the Channel Fader Start
feature starts.)

• [OFF]

The Channel Fader Start feature is disabled.

Default setting is

[ON(SYNC OFF)]

Crossfader Start setting

Change the setting for the Crossfader Start feature.
Setting item:

[CR FDR START]

• [ON(SYNC ON)]

The Crossfader Start feature is enabled with the Sync feature. (The
Sync feature is activated when the Crossfader Start feature starts.)

• [ON(SYNC OFF)]

The Crossfader Start feature is enabled without the Sync feature.
(The Sync feature isn’t activated when the Crossfader Start feature
starts.)

• [OFF]

The Crossfader Start feature is disabled.

Default setting is

[ON(SYNC OFF)]

Содержание DDJ-1000STR





































































































































Результаты поиска

Содержание DDJ-1000STR

Отзывы:

Похожие инструкции для DDJ-1000STR

Бренды по названию

Популярные бренды

PIONEER DJ DDJ-1000STR, Руководство по эксплуатации

Результаты поиска

Содержание DDJ-1000STR

Отзывы:

Похожие инструкции для DDJ-1000STR

Бренды по названию

Популярные бренды