PIONEER DJ DDJ-1000STR Скачать руководство пользователя страница 51

Страница: 51 / 132

Basic use

5 Turn the

[MASTER LEVEL]

knob to adjust the volume level of the

speakers.

Adjust the sound level output from the

[MASTER]

output terminals to an

appropriate level.

•

If you’re outputting sound from the speaker of your PC/Mac, adjust the
speaker volume on the PC/Mac instead of using the

[MASTER LEVEL]

knob.

Monitoring with headphones

1 Set the positions of knobs, etc. as shown below.

• [HEADPHONES MIX]

knob: Center

• [HEADPHONES LEVEL]

knob: Turned fully counterclockwise

2 Press the headphones

[CUE]

button for channel 1.

3 Turn the

[HEADPHONES LEVEL]

knob.

Adjust the headphones volume to a level you’re happy with.

Note

This unit and the Serato DJ Pro software include a variety of features
enabling characteristic DJ performances. For details on the respective
features, read this manual and the Serato DJ Pro software manual.

•

The Serato DJ Pro software manual can be downloaded from Serato.com. For
details, see: Downloading the Serato DJ Pro software manual (page 6).

Содержание DDJ-1000STR





































































































































Результаты поиска

Содержание DDJ-1000STR

Отзывы:

Похожие инструкции для DDJ-1000STR

Бренды по названию

Популярные бренды

PIONEER DJ DDJ-1000STR, Руководство по эксплуатации

Результаты поиска

Содержание DDJ-1000STR

Отзывы:

Похожие инструкции для DDJ-1000STR

Бренды по названию

Популярные бренды