Pilz 632020 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 67

background image

PSEN opII3H Series

Operating Manual PSEN opII3H Series
1003503-EN-05

| 29

14,5

6

6,3

19

Bore holes in the installation surface (two M6 screw
boreholes per flexible bracket) for mounting the flexible
brackets for the transmitter and receiver.

[1]

Fix the transmitter and receiver and their flexible
brackets in place on the installation surface.

For each bracket, use two mounting screws with wash-

included in delivery [

. If necessary,

mounting screws with deviating lengths can be used.

Transmitters and receivers can be shifted vertically
and horizontally.

Screws are only tightened to the final torque during
alignment.

Ensure that the transmitters and receivers are properly
installed in a suitable place.
Ensure that the transmitters and receivers are posi-
tioned at the same height and parallel to one another.

«
...
27
28
29
30
31
...
»

Содержание 632020




































































Отзывы:

Нет отзывов

Похожие инструкции для 632020

Welcome M21311P1-A

Бренд: ABB Страницы: 15

Бренд: V-Tec Страницы: 24

Бренд: GBO Technology Страницы: 103

Бренд: hager Страницы: 2

Intellex DV16000

Бренд: American Dynamics Страницы: 201

Бренд: Agile Remote Cameras Страницы: 4

Бренд: FLIR Страницы: 104

Domotify WI-FI Camera

Бренд: WOXTER Страницы: 65

Бренд: Takex Страницы: 8

Бренд: SAFE-T-ALERT Страницы: 5

Бренд: Bircher Reglomat Страницы: 24

Big Lock Easy Home Basic BAC-20

Бренд: Camos Страницы: 22

Бренд: Young Shin Electronics Страницы: 10

Бренд: BUCKINGHAM MFG Страницы: 5

Бренд: Velleman Страницы: 21

STI-6400 Exit Stopper

Бренд: Safety Technology International Страницы: 7

Бренд: SVBONY Страницы: 41

Бренд: urmet domus Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды