manualshive.com logo in svg

PI PZ265E, Руководство пользователя, Страница: 34 / 63

Поделиться
Скачать
PI PZ265E Скачать руководство пользователя страница 34

 

 

5 Installation 

30 

Version: 1.0.0 

PZ265E 

PL0xx/PDxxx Piezo Actuator 

 

If the PL0xx/PDxxx is not short-circuited: The PL0xx/PDxxx is discharged (p. 40). 

 

The electronics are 

switched off

. 

 

The electronics have a single-pole LEMO socket. 

 

Models without stranded wires: You have soldered (p. 22) or glued (p. 24) a red 

stranded wire to the positive electrode (+) and a black stranded wire to the negative 

electrode (-) of the PL0xx/PDxxx. 

Tools and accessories 

 

P-890.xx coaxial cable (p. 12), LEMO single-pole to open end (can be ordered 

separately) 

 

Suitable soldering iron 

 

Suitable solder 

 

Suitable cable tools 

Connecting the PL0xx/PDxxx to the electronics 

1.

 

If necessary, shorten the wire and the cable shield of the coaxial cable to the correct 

length. 

2.

 

Make the stranded wires of the PL0xx/PDxxx accessible: 

−

 

When the stranded wires of the PL0xx/PDxxx are short-circuited, disconnect the 

connection between the stranded wires. 

−

 

Remove all aids and components that have been connected to the PL0xx/PDxxx for 

short-circuiting or discharging (e.g., conductive rubber or discharging resistor). 

3.

 

Solder the red stranded wire of the PL0xx/PDxxx to the wire of the coaxial cable that is 

connected to the inner contact of the LEMO connector. 

4.

 

Solder the black stranded wire of the PL0xx/PDxxx to the cable shield of the coaxial 

cable. 

5.

 

Insulate the soldered cable connections in a suitable manner. 

6.

 

Connect the connector of the PL0xx/PDxxx to the corresponding connection on the 

electronics. 

 

Содержание PZ265E
































































Отзывы:

Нет отзывов