Physipro XL 5 Скачать руководство пользователя страница 70

Страница: 70 / 104

XL5 and XL RF

ENGLISH

Anti-Tips

Physipro Inc. recommends the installation of anti-tips on all wheelchairs.

Installing anti-tips

1. Press button pin

, so that the lock

pin is drawn inside the tube.

2. Insert anti-tip into the receiver.

3. Slide and turn the anti-tip tube until

the button pin

and lock pin are

positioned through the receiver’s
mounting hole.

4. Repeat the process for the second

anti-tip.

Adjusting anti-tips

Once anti-tips are installed, it is important to adjust their height.

1. Press button pin

and raise or lower the anti-tip’s adjustment tube until button

is positioned in the adjustment hole corresponding to desired height.

2. Repeat the process for the second anti-tip.

Note

- For maximum safety, it is recommended that anti-tips be installed no higher

than 2" above the ground.

Removing anti-tips

To remove the anti-tips, simply press on button pin

and pull anti-tip downwards

until completely extracted from the receiver.

Disengaging anti-tips

When being pushed by an attendant or when clearing an obstacle, anti-tips should
be disengaged.

1. Press and hold button pin

2. Turn the anti-tips inward, towards the center of the frame.
3. Repeat the process for the second anti-tip.

4. After an obstacle is cleared or if the occupant is left unattended, replace the anti-

tips in their initial position. Make sure anti-tips are locked in place.

Содержание XL 5









































































































Результаты поиска

Содержание XL 5

Отзывы:

Physipro XL 5, Руководство пользователя, Страница: 70 / 104

Результаты поиска

Содержание XL 5

Отзывы: