Physipro XL 5 страница 46 Скачать руководство пользователя

Страница: 46 / 104

XL5 and XL RF

ENGLISH

Pneumatic tires (option)

If your wheelchair is equipped with pneumatic tires the following steps should be
followed to install the inner tube and inflate the tires securely.

Installing the inner tube

1. Before installing an inner tube, make sure the

rim and the inside of the tire are clean.

2. Inflate the inner tube slightly.

3. Position the inner tube valve through the hole

in the rim.

4. Insert the inner tube inside the tire.

Note -

Make sure to properly position the inner

tube on the rim and inside the tire. The inner tube
must not be twisted or stick out of the tire.

Inflating the tire

1. Look on the outer tire for the recommended

pressure.

2. Connect pump to inner tube valve.

3. Inflate tire, using a pressure gauge to regularly

check tire pressure. Do not exceed the
recommended tire pressure.

Note

- Tire pressure can vary from one

manufacturer to another, always check the
recommended air pressure indicated on the outer
tire.

WARNING
•

Never use a wheelchair without properly inflate tires, the recommended
tire pressure is indicated on the outer tire.

•

Check tire pressure weekly, as recommended in the

Maintenance

Checklist

•

Overinflated tires can burst, while under inflated tires can deform. Tire
deformation can cause the wheel locks to slip and allow the wheel to spin
unexpectedly, this can potentially lead to a loss of control of your
wheelchair.

•

Proper inflation will extend the lifespan of your tires and improve ease-of-
use.

Содержание XL 5









































































































Результаты поиска

Содержание XL 5

Отзывы:

Похожие инструкции для XL 5

Бренды по названию

Популярные бренды

Physipro XL 5, Руководство пользователя

Результаты поиска

Содержание XL 5

Отзывы:

Похожие инструкции для XL 5

Бренды по названию

Популярные бренды