Phoenix Advanced pressure monitor II Скачать руководство пользователя страница 30

Страница: 30 / 46

MKT-0262 MPC-1748 Rev 02/13

Ancillary Product Specifications

Model 264 Pressure Transducer

RSS of non-linearity, hystereis and non-repeatability.

Units calibrated at nominal 70 °F. Maximum thermal error computed from this datum.

Operating temperature limits of the electronics only. Pressure media temperatures may be considerably higher.

Calibrated into a 50K

load, operable into a 5K

load or greater.

Zero output factory set to within

50 mV (

25 mV for optional accuracies).

Span (full scale) output factory set to within

50 mV (

25 mV for optional accuracies).

Calibrated at factory with a 24 Vdc loop supply voltage and a 250

load.

Zero output factory set to within ± 0.16 mA (± 0.08 mA for optional accuracies).

Span (full scale) output factory set to within ± 0.16 mA (± 0.08 mA for optional accuracies).

Pressure Fittings

3/16" OD barbed brass pressure fitting for 1/4" push-on tubing

Zero and Span Adjustments

Accessible on top of case

Weight (approximate)

10 ounces

Pressure Media

Typically air or similar non-conducting gases

Electrical Data—Voltage

Circuit

3-wire (Com, Exc, Out)

Excitation

9 - 30 Vdc

Output

0 - 5 Vdc

Bi-directional output at zero pressure

2.5 Vdc

Output impedance

100

Electrical Data—Current

Circuit

2-wire

Output

4 - 20 mA

Bi-directional output at zero pressure

12 mA

Minimum supply voltage (Vdc)

9+0.02 x (resistance of receiver plus line)

Maximum supply voltage (Vdc)

30+0.004 x (resistance of receiver plus line)

Содержание Advanced pressure monitor II















































Результаты поиска

Содержание Advanced pressure monitor II

Отзывы:

Похожие инструкции для Advanced pressure monitor II

Бренды по названию

Популярные бренды

Phoenix Advanced pressure monitor II, Руководство по установке

Результаты поиска

Содержание Advanced pressure monitor II

Отзывы:

Похожие инструкции для Advanced pressure monitor II

Бренды по названию

Популярные бренды