Phoenix Advanced pressure monitor II Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 46

background image

Fitting an APM2 in an APM100 Enclosure

Instructions

15

MKT-0262 MPC-1748 Rev 02/13

APM2 Rough-In Installation Guide

2.2.2 Ensure Existing APM1 Enclosure Is Prepared For APM2 Unit

1. Make sure the wall surface around the existing enclosure is flat and clean with no wall damage or holes

beyond the electrical box.

2. A full 5.18" of the center of the existing enclosure will be occupied by the APM2 unit when it is installed.

Any wires or tubing in this region of the electrical box should be moved to the outer perimeter of the
enclosure so the APM2 can slide in without obstructions. You may need to use the knockouts on either
sides, tops or bottom as shown below.

Figure 2-2.

APM100 Knockout Locations

2.2.3 Attach the Base APM2 Unit

Mount the base APM2 unit to the adapter plate using the four supplied phillips head screws. Leaving screws
slightly loose adjust the cover so that it is square. Securely tighten so that the back of the cover is tight to the
finish wall surface.

Figure 2-3.

Installing APM2 to the Adapter Plate

Four phillips head
screws provided

«
...
17
18
19
20
21
...
»

Содержание Advanced pressure monitor II















































Отзывы:

Нет отзывов

Похожие инструкции для Advanced pressure monitor II

Бренд: NAiS Страницы: 208

UltraView iAP1700

Бренд: I-Tech Страницы: 28

Бренд: Panasonic Страницы: 32

Бренд: NewCommWorld Страницы: 19

Бренд: LifeSource Страницы: 13

Бренд: A&D Страницы: 64

Бренд: Elvid Страницы: 17

Бренд: Samtron Страницы: 57

Бренд: Mace Страницы: 2

HEART RATE MONITOR STRAP

Бренд: 3SIXT Страницы: 6

IDS-3106 Series

Бренд: Advantech Страницы: 24

Бренд: AOC Страницы: 47

Vision Pro 150TFT 2206 Series

Бренд: Suzohapp Страницы: 10

PDK 102C-0WG03L

Бренд: IEE Страницы: 6

Бренд: Hanns.G Страницы: 28

Бренд: Torch-Bigtide Страницы: 28

Adelpia SAT22LAN

Бренд: AOC Страницы: 91

Бренд: JARLTECH Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды