Phoenix Contact IOL MA8 PN DI8 Скачать руководство пользователя страница 48

Страница: 48 / 84

IOL MA8 PN DI8

PHOENIX CONTACT

4022_en_A

OPC UA Settings parameters

The following table provides information about the “OPC UA Settings” page.

Table 5-7

“OPC UA Settings” parameters

Field name

Function

OPC UA Server Enable

Default:

Disable

This option controls whether or not the OPC UA server runs on the IOL MA8 PN DI8.

Work-around for faulty OPC UA

clients that require unique

browsenames

Default:

Disable

Enables an alternative set of browse names where each node’s browse name is

unique. Normally only browse paths are required to be unique.

Allow OPC UA clients to write PDO

data

Default:

Disable

Determines whether OPC UA clients are allowed to write PDO data to the IOL MA8

PN DI8 slaves.

Allow OPC UA clients to write ISDU

data

Default:

Disable

Determines whether OPC UA clients are allowed to write ISDU data to the IOL MA8

PN DI8 slaves.

Содержание IOL MA8 PN DI8





















































































Результаты поиска

Содержание IOL MA8 PN DI8

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact IOL MA8 PN DI8, Руководство пользователя

Результаты поиска

Содержание IOL MA8 PN DI8

Отзывы:

Бренды по названию

Популярные бренды