Phoenix Contact IOL MA8 PN DI8 Скачать руководство пользователя страница 11

Страница: 11 / 84

Installation

4022_en_A

PHOENIX CONTACT

3.3

Connecting the power supply

The device can be connected to a single power source or two power sources for

redundancy. The IOL MA8 PN DI8 is powered using a +24 V DC SELV power supply. The

power supply is connected by way of push-in terminal blocks (24 V and 0 V).

Figure 3-3

Single power supply connection

Figure 3-4

Redundant power supply connection

CAUTION:

Incorrect connection may result in damage to equipment and/or serious personal injury.

Only qualified personnel may connect the power, start up, and operate this device.

According to the safety instructions in this text, qualified personnel are persons who are

authorized to start up, to ground, and to mark devices, systems, and equipment according

to the standards of safety technology. In addition, these persons must be familiar with all

warning instructions and maintenance measures in this text.

Disregarding this warning may result in damage to equipment and/or serious personal

injury.

24V

Содержание IOL MA8 PN DI8





















































































Результаты поиска

Содержание IOL MA8 PN DI8

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact IOL MA8 PN DI8, Руководство пользователя

Результаты поиска

Содержание IOL MA8 PN DI8

Отзывы:

Бренды по названию

Популярные бренды