Phoenix Contact 1201132 Скачать руководство пользователя страница 89

Страница: 89 / 148

Warning Codes

109908_en_00

PHOENIX CONTACT

89 / 146

Display on control panel

Warning name

Description

- over temperature warning Over

temperature

warning

(ot)

Over temperature (PTC),

when parameter PTC is set

to enable.

Warning and reset

Warning condition

PTC input voltage is

≤

8.74 V

Warning time

Immediately act

Reset method

Auto

Reset condition

Reset when the input voltage is higher than reset level:

≥

9.25 V and <9.99 V

Cause

Corrective actions

Motor blocked

Clear the motor blocking.

The load is too large

Decrease the loading.

Replace with a motor with a larger power.

Ambient temperature is too high

Change the installed place if there are heating devices in the

surroundings.

Install / add cooling fans or air conditioner to lower the ambi-

ent temperature.

Motor cooling system fault

Check the cooling system and clear the fault if there is any.

Motor fan error

Replace the fan.

Содержание 1201132





















































































































































Результаты поиска

Содержание 1201132

Отзывы:

Похожие инструкции для 1201132

Бренды по названию

Популярные бренды

Phoenix Contact 1201132, Руководство пользователя

Результаты поиска

Содержание 1201132

Отзывы:

Похожие инструкции для 1201132

Бренды по названию

Популярные бренды