Phoenix Contact 1201132 Скачать руководство пользователя страница 11

Страница: 11 / 148

For your safety

109908_en_00

PHOENIX CONTACT

11 / 146

1.4

Safety notes

–

Installation, operation, and maintenance may only be carried out by qualified

electricians. Follow the installation instructions as described.

–

When installing and operating the device, observe the applicable regulations and

safety directives (including national safety directives), as well as general technical

regulations.

–

Install the device in accordance with the instructions described in the installation notes.

Accessing circuits within the device is prohibited.

–

Only clean the device with a suitable damp cloth. Do not use abrasive cleaners or

aggressive solvents. Switch off the device before cleaning and disconnect the device

from the power distribution.

–

Ensure that all devices and adapters are attached and connected correctly to prevent

the devices from being damaged.

–

Refer to the documentation before installation.

The "attention symbol" on the device label means:

Read the safety and installation notes in their entirety.

Failure to follow the instructions may impair the safety features provided.

The "high voltage symbol" on the device label means: Dangerous contact voltage

Only qualified personnel may do this work. The personnel must be familiar with the

necessary safety precautions.

Failure to follow the instructions may result in damage or injury.

The "hot surfaces symbol" on the device label means:

The surfaces of the device may get hot.

Use personal protective equipment or wait for cooling-off.

Failure to follow the instructions may result in damage or injury.

Содержание 1201132





















































































































































Результаты поиска

Содержание 1201132

Отзывы:

Похожие инструкции для 1201132

Бренды по названию

Популярные бренды

Phoenix Contact 1201132, Руководство пользователя

Результаты поиска

Содержание 1201132

Отзывы:

Похожие инструкции для 1201132

Бренды по названию

Популярные бренды