Philips VARILITE VL1100 LED Luminaire Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 87

background image

T

ROUBLESHOOTING

AND

M

AINTENANCE

A

02.1602.0002

13 June 2017

67

Routine Maintenance

Cleaning Optical Lenses and Gobos

WARNING:

Remove power from luminaire before performing maintenance.

The front lens and gobos may require cleaning after extended use. Use only isopropyl alcohol, along
with a soft, lint-free cloth to clean glass components.
To access gobos, refer to procedure below.

Rotating Gobo Replacement

WARNING:

Remove power from luminaire before performing maintenance. Gobos may be HOT

after operation. Allow to cool before replacing.

WARNING:

Users of VARI

❋

LITE® luminaires should not install or use metal gobos.

The use of metal gobos in any VARI

❋

LITE® product may damage the luminaire and

could void the luminaire’s warranty.

To replace a rotating gobo:

Step 1. Remove power from luminaire.
Step 2. At either side of head assembly, press in front cover latch and pull cover straight back until

stopped by tether.

Step 3. Rotate gobo wheel until required gobo position is accessible at finger access cutout.
Step 4. Rotate gobo gear until open end of carrier is upward.

CAUTION:

Do not touch gobos with bare fingers. Wear cotton gloves or other covering while

replacing. Clean with isopropyl alcohol and soft, lint-free cloth if required.

CAUTION:

Do not pull metal spring clip carrier back too far or it will not close properly.

Step 5. If applicable, carefully pull current gobo up and out of carrier.

Gobo can be easily scratched

on sides of carrier if not careful.

Step 6. Carefully install new gobo, orienting side marked “This Edge In” toward center of gobo

wheel and side marked “Lamp Side” (mirror finish) toward lamp.

Gobo can be easily

scratched on sides of carrier if not careful.

Ensure gobo is firmly set in carrier grooves.

«
...
79
80
81
82
83
...
»

Содержание VARILITE VL1100 LED Luminaire
























































































Отзывы:

Нет отзывов

Похожие инструкции для VARILITE VL1100 LED Luminaire

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: Rapid Technic Страницы: 152

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренд: Masterclock Страницы: 19

Ti-Max NLX nano

Бренд: NSK Страницы: 38

Бренд: Sensio Страницы: 3

Бренд: Zafferano Страницы: 28

Бренд: Basler Страницы: 33

DynaTrap DT1260-TUN

Бренд: Dynamic Страницы: 4

Бренд: Elma Страницы: 35

Бренд: Qtx Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды