Philips Fisio 311 Скачать руководство пользователя страница 13

Страница: 13 / 42

Départ. Technical support- CM640

PROCEDURE

COMPANY RESTRICTED

PHILIPS Consumer

Communications

Centre du Mans

Service Repair Support

VY-V-640-204

Page : 13 of 42
Langue : EN
Date : 09/21/01



PHILIPS ELECTRONICS N.V. 1999

VY-V-640-204

8.0 TEST PROCEDURES

8.1

Initial Functional Check for Fisio 311

8.1.1

Insert the Test Production Card into the SIM Reader at the back of the cellular phone and clip a charged
battery on the phone.

8.1.2

Press the «ON» button for 2 seconds at least and the LCD will show a message which contains information
of FA (Final Adjustment) status and 12NC.

8.1.3

Follow the instructions as mentioned below :

Step

Procedure

Observation

Press Key 1

Press Key 1 again.

Continue Buzzer signal

Left corner displays 1
00

Press key 2
(Audio loop local effect)

Press key 2 again

"LocalEffect"
" XX XX XX“
“ XX XX”
Left corner displays 2
01

Press key 3
Audio loop test (Speak to Mic
and listen echo from Speaker)

Press key 3 again

"AUDIO xx xx xx xx”
"EEP xx xx xxxx ”

Left corner displays 3
02

Press key 4
Check for the Backlight
function in the same time.

Press key 4 again

Backlight must be on

Left corner displays 4
03

Press Key 5
(Checkerboard test)

Press Key 5 again

Checkerboard 1 pixel on

Left corner displays 5
04

Press Key 6
(Inverted Checkerboard)

Press Key 6 again

Checkerboard 2 pixel on

Left corner displays 6
05

Содержание Fisio 311











































Результаты поиска

Содержание Fisio 311

Отзывы:

Похожие инструкции для Fisio 311

Бренды по названию

Популярные бренды

Philips Fisio 311, Руководство по обслуживанию

Результаты поиска

Содержание Fisio 311

Отзывы:

Похожие инструкции для Fisio 311

Бренды по названию

Популярные бренды