Philips DP-IF8000, Руководство по обслуживанию

Страница: 6 / 38

6
DP-IF8000
• MAIN DSP-DIAT period
Check RCS (IC12-109pin), BCK (IC12-106), VPOUT1 (IC12-
96pin), RINFO (IC12-107pin).
Turn the power on, set in Digital Input mode, and select VIRTUAL
FRONT, or VIRTUAL 5.1 or VIRTUAL 6.1 with the OUTPUT
switch.
The view on the monitor when the input source sampling frequency
is 48 kHz is shown in Fig. 11.
The view on the monitor when the input source sampling frequency
is 44.1 kHz is shown in Fig. 12.
The view on the monitor when the input source sampling frequency
is 32 kHz is shown in Fig. 13.
Fig 9
LRCK
BCK
LPOUT2
Lch Rch
Note 3: Example shows 48 kHz for LRCK, 44.1 kHz and
32 kHz are also used.
Fig 10
LRCK
BCK
VPOUT2
Fig 11
RCS
BCK
VPOU1
RINFO
0001000 t fs=48k
Note 4: fs=48kHz
Fig 12
RCS
BCK
VPOU1
RINFO
0000000 t fs=44.1k
Note 5: fs=44.1kHz
Fig 13
RCS
BCK
VPOU1
RINFO
0011000 t fs=32k
Note 6: fs=32kHz
When OFF is selected with the OUTPUT key, check the DILRCK
(IC12-98pin), BCK (IC12-106pin), VPOUT1 (IC12-96pin), and the
view on the monitor should be the same as the MAIN DSP-DAC
period.
2.1.2 System Control
Note: Input a signal of some kind to DIGITAL IN 1 and LINE IN.
• MICON-DIR period
Check the DIR_XCS (IC4-37pin), SCK2 (IC4-38pin), and SDO2
(IC4-36pin).
Figure 14 shows the view on the monitor after power is turned on,
at the instant of switching with the INPUT key.
Fig 14
DIR_XCS
SCK
(500KHZ)
SDO2
Address
8 bit
00010111 data
8 bit + 8 bit
• MICON-DAC period
Check the DAC_XCS (IC5-10pin), SCKO (IC5-8pin), and SDO02
(IC5-9pin).
Figure 15 shows the view on the monitor after power is turned on,
at the instant of switching with the INPUT key.
Fig 15
DAC_XCS
SCK 0
(500KHZ)
SDO 0
Address
8 bit
00100000 data
8 bit + 8 bit
• MICON-LED DRIVER period
Check the LED_XLAT (CN102-3pin), SCKO(CN102-6pin), and
SDO(CN102-7pin).
Figure 16 shows the view on the monitor after power is turned on,
at the instant of switching with each key.
Fig 16
LED_XLAT
SCK 0
(500KHZ)
SDO 0
8 bit + 8 bit
after data transfer LAT
• MICON-DIAT period
Check the DIAT_LAT (IC12-152pin), SCKO (IC12-151pin), SDO
(IC12-153pin).
Figure 17 shows the view on the monitor after power is turned on,
at the instant of switching with the INPUT key. The timing is shown
in detail in FIG. 18.
Fig 17
DIAT_LAT
SCK 0
SDO 0
Fig 18
DIAT_LAT
SCK 0
(500KHZ)
SDO 0
after 24bit data transfer LAT