Philips 32PFL7332/93, Руководство по обслуживанию

Страница: 86 / 109

Alignments EN 86 LC7.1A LA 8.
• When finished return to the SAM root menu and press
STANDBY on the RC to store the aligned values to the
NVM.
Table 8-2 Tint settings
(*) This data was not available at the time of writing, but for
default settings use the column on the right.
Black Level Offset Alignment
• Activate SAM.
• Select “RGB Align.” -> “BlackL Offset” and choose a colour.
• Set all “BlackL Offset” values to “0”.
• When finished return to the SAM root menu and press
STANDBY on the RC to store the aligned values to the
NVM.
Note: For models with “Pixel Plus”, the “Black Offset” (black
level offset) should NOT be changed in SAM. These offset
values of RGB should be set to “0”, and should
NOT be
adjusted. Any adjustment of these values will affect the low
light white balance.
ADC YPbPr Gray Scale Alignment
When the grey scale is not correct, use this alignment:
•
Activate SAM.
• Select “NVM Editor”.
• Enter address “ 26(dec)” (ADR).
• Set value (VAL) to “197(dec)
±
25”.
• Store (STORE) the value.
8.4 Option Settings
8.4.1 Introduction
The microprocessor communicates with a large number of I
2
C
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence/absence of these specific
ICs (or functions) is made known by the option codes.
Notes:
• After changing the option(s), save them with the STORE
command.
• The new option setting becomes active after the TV is
switched "off" and "on" again with the mains switch (the
EAROM is then read again).
8.4.2 How To Set Option Codes
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set all option numbers. You can find the correct option
numbers in table “Option Codes OP1...OP7“ below.
How to Change Options Codes
An option code (or “option byte”) represents eight different
options (bits). When you change these numbers directly, you
can set all options very quickly. All options are controlled via
seven option numbers (OP1... OP7).
Activate SAM and select “Options”. Now you can select the
option byte (OP1.. OP7) with the CURSOR UP/ DOWN keys,
and enter the new 3 digit (decimal) value. For the correct
factory default settings, see the table “Option codes
OP1...OP7“ below. For more detailed information, see the
second table “Option codes at bit level“. If an option is set
(value “1”), it represents a certain decimal value.
When all the correct options (bits) are set, the sum of the
decimal values of each Option Byte (OP) will give the option
code.
Figure 8-1 Option codes OP1...OP7 (for all LC7.1A models)
Alignment 26” (*) 32” 37” (*) 42”
COOL_RED t.b.d. 250 t.b.d. 249
COOL_GREEN t.b.d. 251 t.b.d. 241
COOL_BLUE t.b.d. 246 t.b.d. 246
NORMAL_RED t.b.d. 252 t.b.d. 251
NORMAL_GREEN t.b.d. 246 t.b.d. 238
NORMAL_BLUE t.b.d. 228 t.b.d. 229
WARM_RED t.b.d. 252 t.b.d. 246
WARM_GREEN t.b.d. 232 t.b.d. 222
WARM_BLUE t.b.d. 197 t.b.d. 199
Sets 12NC Sets Type Panel Type
Panel
Code
(Dec) Option Byte
LC07_China_LCD_basic (/93)
Group 1 Group 2
1 2 3 4 5 6 7
LPL : LC320W01-SL06 046
AUO : T315XW02 VD 091
867000026435 32PFL7332/93
CMO : V315B1-L05 069
064 130 255 009 006
1 0 0 9 2 0
LC07_China_LCD_ambi-light (/93)
LPL : LC320W01-SL06 046
AUO : T315XW02 VD 091 867000032824 32PFL7932/93
CMO : V315B1-L05 069
001
061
H_17270_017.eps
060707