Alignments
6.
Note
1). Example
6.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
“00PF0000000000” and Production code “00000000000000”.
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the “NVM editor” and “Dealer options”
items in SAM (do not forget to “store”).
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. This action also
ensures the correct functioning of the “Net TV” feature and
access to the Net TV portals. The loading of the CTN and
production code can also be done via ComPair (Model number
programming).
After a SSB repair, the original channel map can be restored,
provided that the original channel map was stored on a USB
stick before repair was commenced and that basic functionality
of the TV, needed for this procedure, was not hampered as a
result of the defect. The procedure of “channel map cloning” is
clearly described in the (electronic) user manual.
In case of a display replacement, reset the “Operation hours
display” to “0”, or to the operation hours of the replacement
display.
6.5.1
SSB identification
Whenever ordering a new SSB, it should be noted that the
correct ordering number (12nc) of a SSB is located on a sticker
on the SSB. The format is <12nc SSB><serial number>. The
ordering number of a “Service” SSB is the same as the ordering
number of an initial “factory” SSB.
Figure 6-1 SSB identification
6.6
Cable position numbers
In this chassis, the cable position numbers can be defined via
the rule that the number is always starting with an “E” followed
by the connector number of the current sourcing board. The
order is always seen from where the power initiates from. So
from PSU to SSB, from SSB to IR/LED panel, from IR/LED
panel to keyboard control panel. For example, a cable from the
PSU connector CN902 to the SSB connector CN701, will have
the position number ECN902.
Bit 12
4096
3D Overdrive LUT
000
1)
000 = no overdrive LUT
001 = LUT1
010 = LUT2
011 = LUT3
100 = LUT4
101 = LUT5
110 = LUT6
111 = LUT7
Bit 11
2048
Bit 10
1024
Bit 9
512
ISF
0
1)
0 = OFF
1 = ON
Bit 8
256
DVB-S channel d new LNB 0
1)
0 = OFF
1 = channel decoder STV 0 LNBH25
Bit 7
128
MSB Light Sensor type
0
1)
-
Bit 6
64
DVB-T2 Sony channel decoder
1
1)
0 = OFF
1 = channel decoder T2: CXD2834ER
Bit 5
32
FPGA PQ
0
1)
0 = not present
1 = present
Bit 4
16
2player gaming
1
1)
0 = OFF
1 = ON
Bit 3
8
WM DRM10
1
1)
0 = OFF
1 = ON
Bit 2
4
HBBTV
1
1)
0 = OFF
1 = ON
Bit 1
2
DVB-T2 Installation
0
1)
0 = no installation
1 = country depending
Bit 0 (LSB)
1
DVB-T2
1
1)
0 = OFF
1 = channel decoder 2
Option & Bit
Dec. Value
Option Name
Prescribed Value
1)
Description
1
83
10_221_090
3
1
8
.ep
s
090
3
19