Philio Technology Corporation PAN10 Скачать руководство пользователя страница 12

ital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interfer-

ence to radio communications. 

However, there is no guarantee that interference will not occur in a particular installa-

tion. 

If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that 

may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party re-

sponsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other an -

tenna or transmitter.

警語: 

「取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻

率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應

立即停用,並改善至無干擾時方得繼續使用。

前述合法通信,指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通

信或工業、科學及醫療用電波輻射性電機設備之干擾。」

12

Содержание PAN10













Отзывы: