PHICOMM FD-364N Скачать руководство пользователя

Страница: 58 / 61

150Mbps Wireless N ADSL2/2+ Modem Router

www.phicomm.com

Appendix B: Certification

•

This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.

CE Mark Warning

Marking with the above symbol indicates compliance with the Essential Requirements of the

R&TTE Directive of the European Union (1999/5/EC).

This is a class B product. In a domestic environment, this product may cause radio interference,

in which case the user may be required to take adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following
the EU Directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country

Restriction

Reason/remark

Bulgaria

None

General authorization required for outdoor use and public

service

France

Outdoor use limited to 10 mW

e.i.r.p. within the band

2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band has

been ongoing in recent years to allow current relaxed

regulation. Full implementation planned 2012

Italy

None

If used outside of own premises, general authorization is

required

Luxembourg

None

General authorization required for network and service

supply(not for spectrum)

Norway

Implemented

This subsection does not apply for the geographical area within

a radius of 20 km from the centre of Ny-Ålesund

Russian

Federation

None

Only for indoor applications

Note

Please don’t use the product outdoors in France.

Содержание FD-364N





























































Результаты поиска

Содержание FD-364N

Отзывы:

Похожие инструкции для FD-364N

Бренды по названию

Популярные бренды

PHICOMM FD-364N, Руководство пользователя

Результаты поиска

Содержание FD-364N

Отзывы:

Похожие инструкции для FD-364N

Бренды по названию

Популярные бренды