Phcbi MCO-80ICL Скачать руководство пользователя страница 40

Страница: 40 / 44

SPECIFICATIONS

Product name

Incubator MCO-80ICL

External dimensions

W986 mm x D853 mm x H2,040 mm (without caster; H1,975 mm)

Internal dimensions

W806 mm x D693 mm x H1,524 mm

Interior volume

851 L

Exterior

Painted steel

Interior

Stainless steel containing copper

Outer door

Double glass with door heater

Outer door latch

Tray

5 trays made of stainless steel containing copper

W776 mm x D659 mm x H10 mm, Maximum load; 30 kg/tray

Access port

Inner diameter; 40 mm, Two locations, each on both sides

Insulation

Slab board

Heater

Main heater: 600 W, Water reservoir heater: 211 W, Door frame heater: 125 W,

Flange heater: 250 W, Glass heater: 150 W

Humidifying system

Normal mode: Natural evaporation with humidifying water

High humidity mode: Heated evaporation with humidifying water

Temperature controller

PID control system

Temperature display

Digital display

controller

PID control system

density display

Digital display

Air circulation

Fan assisted

Air filter

0.3

m, Efficiency; 99.97 % or more

Water level sensor

Thermal type

Alarm

High/Low temperature alarm, CO

density alarm, Upper limit temperature alarm
Door alarm

Remote alarm contact

Allowable contact capacity: DC 30 V, 2 A

inlet connection

4 mm to 6 mm diameter tube

inlet pressure

0.1 MPa(G) (1.0 kgf/cm

(G), 14.5 psi(G))

Accessories

5 trays, 5 sets of tray support, 1 gas tube, 2 tube bands, 1 drain tank (6.5 L)

Power source

Single phase, 110 V-120 V, 60 Hz

Inside power outlet

Two sockets (Up to 3 A in total)

Use condition: Inner temperature below 40

C and humidity below 50%R.H.

Outer power outlet

Two sockets (Up to 1 A in total)

Weight

275 kg

Optional accessory

Gas auto changer (MCO-80GC)

Tray (MCO-80ST) Same tray as the attached one including 2 tray supports

Roller bottle rack mount (MCO-80RBS)

Small door (MCO-80ID), UV system set (MCO-80UVS),

Auto water supply system (MCO-80AS),

Interface board (MCO-420MA, USA only),

Interface board (MTR-480)*, Interface board (MTR-L03)*

*Only for the Data acquisition system MTR-5000 user.

Note

: Refer to the updated catalog when ordering an optional component.

Designs and specifications are subject to change without notice.

Содержание MCO-80ICL













































Результаты поиска

Содержание MCO-80ICL

Отзывы:

Бренды по названию

Популярные бренды

Phcbi MCO-80ICL, Руководство по эксплуатации

Результаты поиска

Содержание MCO-80ICL

Отзывы:

Бренды по названию

Популярные бренды