PG Drives Technology R-NET OMNI Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 174

background image

PG D

RIVES

T

ECHNOLOGY

O

MNI

– S

TANDARD

- O

PERATION

SK78813/5

61

diagnostic screen at this time. You can reset this condition by switching the
control system off and on again.

11.4.8 Control System Locked

The Control System can be locked in one of two ways. Either using a sequence
of  deflections  and  presses  with  a  SID  or  with  a  physical  Key.  How  the  Control
System  is  locked  depends  on  how  the  wheelchair  manufacturer  has
programmed the system.

11.4.8.1

Keypad Locking

To lock the wheelchair using the keypad:

•

While the control system is switched on, depress On/Off input.

•

After 1 second the control system will beep. Now release the
On/Off input

•

Deflect the SID forwards until the control system beeps.

•

Deflect the SID in reverse until the control system beeps.

•

Release the SID, there will be a long beep.

•

The wheelchair is now locked.

The padlock will be displayed if the Omni is switched back on.

To unlock the wheelchair:

•

If the control system has switched off, press the On/Off input.

•

Deflect the SID forwards until the control system beeps.

•

Deflect the SID in reverse until the control system beeps.

•

Release the SID, there will be a long beep.

«
...
59
60
61
62
63
...
»

Содержание R-NET OMNI















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R-NET OMNI

KM-5000 recliner Series

Бренд: Karma Страницы: 36

Бренд: Invacare Страницы: 76

Бренд: Vela Страницы: 2

Бренд: Motion Concepts Страницы: 88

Бренд: Care Quip Страницы: 2

Бренд: Ranger Страницы: 17

Бренд: R82 Страницы: 8

Бренд: Sunrise Medical Страницы: 96

S-Ergo 105(KM-1500?3)

Бренд: Karman Healthcare Страницы: 32

Бренд: Handicare Страницы: 12

Бренд: Karma Страницы: 40

Бренд: Karma Страницы: 48

Бренд: Karma Страницы: 52

Бренд: Karma Страницы: 60

Бренд: Karma Страницы: 64

Morgan KISS Seat

Бренд: Karma Страницы: 116

Бренд: UPnRIDE Robotics Страницы: 90

Бренд: Martin Innovations Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды