PG Drives Technology R-NET OMNI Скачать руководство пользователя страница 59

Страница: 59 / 174

PG D

RIVES

ECHNOLOGY

MNI

– S

TANDARD

- O

PERATION

SK78813/5

11.4

Message Window

The Omni displays warning icons and informational messages, in a dedicated
message window, as seen below.

11.4.1 Restart

When the control system requires a reboot; for example, after a
module re-configuration, this symbol will be flashed.

11.4.2 Timer

This  symbol  is  displayed  when  the  control  system  is  changing
between  different  states.  An  example  would  be  entering  into
Programming  Mode.  The  symbol  is  animated  to  show  the  sands
falling.

11.4.3 Sleep

This symbol is displayed when the Omni has gone into sleep
mode.

11.4.4 Cross & Tick

These symbols will be displayed during configuration procedures.

Process completed correctly.

Содержание R-NET OMNI















































































































































































Результаты поиска

Содержание R-NET OMNI

Отзывы:

PG Drives Technology R-NET OMNI, Техническое руководство, Страница: 59 / 174

Результаты поиска

Содержание R-NET OMNI

Отзывы: