PG Drives Technology R-NET OMNI Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 174

PG Drives Technology R-NET OMNI Скачать руководство пользователя страница 32

PG D

RIVES

T

ECHNOLOGY

O

MNI

– S

TANDARD

- I

NSTALLATION

SK78813/5

32

The  device  comprises  of  three  or  four  direction  switches  and  a  User  Switch
connected to the Omni via the 9-way D-type connector. In addition, a normally
closed User Switch should be connected to the Omni via the 3.5mm/1/8” jack
socket.  This  switch,  although  functionally identical to the switch input on the 9-
way  D-type  connector,  is  required  to  provide  a  fail-safe  emergency  stop
system.

8.5

Sip and Puff Device and User Switch

A sip and puff mouthpiece is connected to the Omni via the pneumatic input.
In addition, a User Switch should be connected to the Omni via the 3.5mm/1/8”
jack socket. This switch is required to provide a fail-safe emergency stop
system.

8.5.1 Sip and Puff Calibration

If a new Sip and Puff SID is fitted, then the following calibration procedure must
be performed to match the Omni to the user’s operating capabilities.

To begin the procedure you must first enter OBP mode. From there, follow the
path detailed below, using the right navigation button on the front of the Omni:

Omni – Global – Sip and Puff – Calibrate

A screen like the one shown below should appear.

Soft  Sip  will  be  highlighted  first.  The  user  must  now  make  a  series  of  soft  sips.
After  each  sip,  a  live  readout  of  the  current  pressure  will  be  displayed  on  the
screen  in  the  form  of  a  line  within  the  0  -  100  scale.  Repeated  soft  sips  will

Deadband

Deadband

Deadband

Deadband

«
...
30
31
32
33
34
...
»

Содержание R-NET OMNI















































































































































































Отзывы:

Нет отзывов