4
NOTE
RHP-8K1U
-12
RHP-8K1U
-24
RHP-8K1U
-48
MODEL
DIMENSION
PACKING
OTHERS
Rack 365*482.6*44(L*W*H, with mounting bracket) ; 365*440*44(L*W*H, without mounting bracket)
5.5Kg
; 3pcs/17.5Kg/2.11CUFT
NOTE
RHB-8K1U
-12
RHB-8K1U
-24
RHB-8K1U
-48
MODEL
VOLTAGE RANGE
Note.2
CHARGER
RACK SHELF
CURRENT RANGE
FREQUENCY RANGE
AC CURRENT (Typ.) per CHARGER
INPUT
OUTPUT
LEAKAGE CURRENT
per CHARGER
90 ~ 264VAC 127 ~ 370VDC
0 ~ 500A
0 ~137.5A
RHP-1UI-A or RHP-1UT-A
RCB-1600-12
RCB-1600-24
RCB-1600-48
47 ~ 63Hz
<1.5mA / 230VAC
14A/115VAC 8A/230VAC
15A/115VAC 8.5A/230VAC
15A/115VAC 8.5A/230VAC
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
DIMENSION
PACKING
OTHERS
-30 ~ +70
(Refer to "Derating Curve")
℃
20 ~ 90% RH non-condensing
-40 ~ +85
, 10 ~ 95% RH non-condensing
℃
±
℃
℃
0.03%/
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
Rack 365*482.6*44(L*W*H, with mounting bracket) ; 365*440*44(L*W*H, without mounting bracket)
ENVIRONMENT
5.5Kg
; 3pcs/17.5Kg/2.11CUFT
ALARM SIGNAL
REMOTE ON-OFF CONTROL
The isolated TTL signal out, Please refer to Installation Manual
By electrical signal or dry contact ON:short OFF:open
FUNCTION
SAFETY &
EMC
(Note 4)
0 ~ 275A
OUTPUT VOLTAGE PROGRAMMABLE(PV)
OUTPUT CURRENT PROGRAMMABLE(PC)
Adjustment of output voltage is allowable to 75 ~ 125% of nominal output voltage. Please refer to the Function Manual.
Adjustment of output current is allowable to 20 ~ 100% of rated current. Please refer to the Function Manual.
14.4V
28.8V
13.8V
27.6V
57.6V
55.2V
BOOST CHARGE VOLTAGE(Vboost)(default)
FLOAT CHARGE VOLTAGE(Vfloat)(default)
TEMPERATURE COMPENSATION
-3mV /
/ cell / (12V = 6 cells ; 24V = 12 cells ; 48V = 24 cells)
℃
SAFETY STANDARDS
WITHSTAND VOLTAGE
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
ISOLATION RESISTANCE
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25
/ 70% RH
℃
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (E 50082-2),
lev , criteria A
N
el
light industry
,
EAC TP TC 020
Compliance to EN55022 (CISPR22) Conduction Class B, Radiation Class A ; EN61000-3-2,-3,
EAC TP TC 020
EMC IMMUNITY
EMC EMISSION
AUXILIARY POWER
5V @ 0.3A, 12V @ 0.8A
Note.5
2.
Mechanical Specification and Input/Output Terminals
2.1 Mechanism of Supply/Charger unit
Figure
2-1
41
85
Air flow
direction
300
11max.
9max.
LED
S
tatus
Indicator
42.5
12.5
5.8
7.7
3.6
CN1
62.4
SVR
7
50
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Under parallel
operation of more than one rack connecting together, ripple of the output voltage may be higher than the SPEC at light load condition. It will go back to
normal ripple level once the output load is more than 5%.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4.
The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a
mm*
mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.
1000
1300
For guidance on how
to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
5. Output of all the RCP-1600 modules are connected in parallel in the rack.
6. Derating may be needed under low input voltages. Please check the static characteristics for more details.
7. Because of component tolerance, there is a possibility that some of units connected in parallel will reach an overcurrent limit then overloading the other
units when operating at full load condition. If overload conditions happen in parallel usage, it is suggested that derate the total output current by 10%.
8. The equivalent leakage current of the system is determined by the quantity of populated rectifiers.
9. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).
℃
℃
UL60950-1, TUV EN60950-1 EAC TP TC 004 approved
,
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
℃
2. Derating may be needed under low input voltages. Please check the static characteristics for more details.
3.
The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a
mm*
mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.
720
360
For guidance on how
to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
4. Output of all the RCB-1600 modules are connected in parallel in the rack.
5. The equivalent leakage current of the system is determined by the quantity of populated rectifiers.
6. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).
℃
℃
6
RCB-1600-RHP-1U_1610-21407-0001-E-0420