manualshive.com logo in svg

PEUGEOT TSDI, Руководство по ремонту

Поделиться
Скачать
PEUGEOT TSDI Скачать руководство пользователя страница 38

SPECIAL WORK AND PROCEDURES

Page: 38

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

To remove the strainer

 

- Remove the ignition key after unlocking the

saddle
 - Remove the saddle/locker assembly
 - Empty the fuel tank proceeding as follows:
 - Disconnect the vent (A) pipe (1) from the gauge
(2) and put into a container in order to drain out the
fuel
 - Reconnect the pipe (1) once the tank is empty
 - Disconnect the fuel gauge
 - Unscrew and remove the fuel gauge (2) with its
seal using tool P/N 756056

 - Remove the strainer (3) by passing one hand
inside the gauge well, wearing a protective glove
 - Clean or change the strainer in accordance with
the service instructions

Re-assembly: 

Re-assemble in the reverse order to

dismantling

 - Tighten the fuel gauge with the ring spanner P/N
756056 in order to line up the arrow with the
centring mark on the tank

Содержание TSDI












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды